Usage: ./wl [-a|i ] [-h] [-d|u|x] [arguments] -h this message and command descriptions -h [cmd] command description for cmd -a, -i adapter name or number -d output format signed integer -u output format unsigned integer -x output format hexdecimal ver get version information cmds generate a short list of available commands up reinitialize and mark adapter up (operational) down reset and mark adapter down (disabled) out mark adapter down but do not reset hardware(disabled) On dualband cards, cards must be bandlocked before use. clk set board clock state. return error for set_clk attempt if the driver is not down 0: clock off 1: clock on restart Restart driver. Driver must already be down. reboot Reboot platform radio Set the radio on or off. "on" or "off" dump Give suboption "list" to list various suboptions srclear Clears first 'len' bytes of the srom, len in decimal or hex Usage: srclear srdump print contents of SPROM to stdout srwrite Write the srom: srwrite byteoffset value srcrc Get the CRC for input binary file ciswrite Write specified to the SDIO CIS source (either SROM or OTP) cisupdate Write a hex byte stream to specified byte offset to the CIS source (either SROM or OTP) --preview option allows you to review the update without committing it [--preview] cisdump Display the content of the SDIO CIS source -b -- also write raw bytes to -- optional count of bytes to display (must be even) cis_source Display which source is used for the SDIO CIS cisconvert Print CIS tuple for given name=value pair rdvar Read a named variable to the srom wrvar Write a named variable to the srom nvram_source Display which source is used for nvram nvram_dump print nvram variables to stdout nvset set an nvram variable name=value (no spaces around '=') nvget get the value of an nvram variable nvram_get get the value of an nvram variable revinfo get hardware revision information customvar1 print the value of customvar1 in hex format msglevel set driver console debugging message bitvector type 'wl msglevel ?' for values phymsglevel set phy debugging message bitvector type 'wl phymsglevel ?' for values PM set driver power management mode: 0: CAM (constantly awake) 1: PS (power-save) 2: FAST PS mode wake set driver power-save mode sleep state: 0: core-managed 1: awake promisc set promiscuous mode ethernet address reception 0 - disable 1 - enable monitor set monitor mode 0 - disable 1 - enable active monitor mode (interface still operates) frag Deprecated. Use fragthresh. rts Deprecated. Use rtsthresh. cwmin Set the cwmin. (integer [1, 255]) cwmax Set the cwmax. (integer [256, 2047]) srl Set the short retry limit. (integer [1, 255]) lrl Set the long retry limit. (integer [1, 255]) rate force a fixed rate: valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54) valid values for 802.11b are (1, 2, 5.5, 11) valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate mrate force a fixed multicast rate: valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54) valid values for 802.11b are (1, 2, 5.5, 11) valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate a_rate force a fixed rate for the A PHY: valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate a_mrate force a fixed multicast rate for the A PHY: valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate bg_rate force a fixed rate for the B/G PHY: valid values for 802.11b are (1, 2, 5.5, 11) valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate bg_mrate force a fixed multicast rate for the B/G PHY: valid values for 802.11b are (1, 2, 5.5, 11) valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate infra Set Infrastructure mode: 0 (IBSS) or 1 (Infra BSS) ap Set AP mode: 0 (STA) or 1 (AP) bssid Get the BSSID value, error if STA and not associated bssmax get number of BSSes channel Set the channel: valid channels for 802.11b/g (2.4GHz band) are 1 through 14 valid channels for 802.11a (5 GHz band) are: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116,120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 184, 188, 192, 196, 200, 204, 208, 212, 216 cur_mcsset Get the current mcs set chanspecs Get all the valid chanspecs (default: all within current locale): -b band (5(a) or 2(b/g)) -w bandwidth, 10,20 or 40 [-c country_abbrev] chanspec Set [a,b][n][u,l] channel number (0-224) band a=5G, b=2G, default to 2G if channel <= 14 bandwidth, n=10, none for 20 & 40 ctl sideband, l=lower, u=upper OR Set channel with legacy format: -c channel number (0-224) -b band (5(a) or 2(b/g)) -w bandwidth, 10,20 or 40 -s ctl sideband, -1=lower, 0=none, 1=upper dfs_channel_forced Set [a,b][n][u,l] channel number (0-224) band a=5G, b=2G, default to 2G if channel <= 14 bandwidth, n=10, non for 20 & 40 ctl sideband, l=lower, u=upper tssical_start_idx Start the tssi cal, Enter the tx pwr index tssical_start Start the tssi cal, Enter the target power in qdBm tssical_power Enter the measured power in qdBm tssical_params Returns the new PA Params tssical_txdelay Enter the delay needed before fast tssi measurement tssi Get the tssi value from radio txpwr Set tx power in milliwatts. Range [1, 84]. txpwr1 Set tx power in in various units. Choose one of (default: dbm): -d dbm units -q quarter dbm units -m milliwatt units Can be combined with: -o turn on override to disable regulatory and other limitations Use wl txpwr -1 to restore defaults txpathpwr Turn the tx path power on or off on 2050 radios txpwrlimit Return current tx power limit powerindex Set the transmit power for A band(0-63). -1 - default value atten Set the transmit attenuation for B band. Args: bb radio txctl1. auto to revert to automatic control manual to supspend automatic control phyreg Get/Set a phy register: offset [ value ] [ band ] radioreg Get/Set a radio register: offset [ value ] [ band/core ] ucflags Get/Set ucode flags 1, 2, 3(16 bits each) offset [ value ] [ band ] shmem Get/Set a shared memory location: offset [ value ] [band ] macreg Get/Set any mac registers(include IHR and SB): macreg offset size[2,4] [ value ] [ band ] ucantdiv Enable/disable ucode antenna diversity (1/0 or on/off) gpioout Set any GPIO pins to any value. Use with caution as GPIOs would be assigned to chipcommon Usage: gpiomask gpioval pcieserdesreg g/set SERDES registers: dev offset [val] ampdu_activate_test actiate ampdu_tid enable/disable per-tid ampdu; usage: wl ampdu_tid [0/1] ampdu_retry_limit_tid Set per-tid ampdu retry limit; usage: wl ampdu_retry_limit_tid [0~31] ampdu_rr_retry_limit_tid Set per-tid ampdu regular rate retry limit; usage: wl ampdu_rr_retry_limit_tid [0~31] ampdu_send_addba send addba to specified ea-tid; usage: wl ampdu_send_addba ampdu_send_delba send delba to specified ea-tid; usage: wl ampdu_send_delba ampdu_clear_dump clear ampdu counters dpt_deny adds/removes ea to dpt deny list usage: wl dpt_deny dpt_endpoint creates/updates/deletes dpt endpoint for ea usage: wl dpt_endpoint dpt_pmk sets DPT pre-shared key dpt_fname sets/gets DPT friendly name dpt_list gets status of all dpt peers bdd_fname sets/gets BDD friendly name actframe Send a Vendor specific Action frame to a channel usage: wl actframe channel dwell-time antdiv Set antenna diversity for rx 0 - force use of antenna 0 1 - force use of antenna 1 3 - automatic selection of antenna diversity txant Set the transmit antenna 0 - force use of antenna 0 1 - force use of antenna 1 3 - use the RX antenna selection that was in force during the most recently received good PLCP header plcphdr Set the plcp header. "long" or "auto" or "debug" phytype Get phy type rateparam set driver rate selection tunables arg 1: tunable id arg 2: tunable value wepstatus Set or Get WEP status wepstatus [on|off] primary_key Set or get index of primary key addwep Set an encryption key. The key must be 5, 13 or 16 bytes long, or 10, 26, 32, or 64 hex digits long. The encryption algorithm is automatically selected based on the key size. keytype is accepted only when key length is 16 bytes/32 hex digits and specifies whether AES-OCB or AES-CCM encryption is used. Default is ccm. WAPI is selected if key len is 32 and arguments contain wapi. addwep [ocb | ccm | wapi] [notx] [xx:xx:xx:xx:xx:xx] rmwep Remove the encryption key at the specified key index. keys Prints a list of the current WEP keys tsc Print Tx Sequence Couter for key at specified key index. wsec_test Generate wsec errors wsec_test type 'wl wsec_test ?' for test_types tkip_countermeasures Enable or disable TKIP countermeasures (TKIP-enabled AP only) 0 - disable 1 - enable wsec_restrict Drop unencrypted packets if WSEC is enabled 0 - disable 1 - enable eap restrict traffic to 802.1X packets until 802.1X authorization succeeds 0 - disable 1 - enable cur_etheraddr Get/set the current hw address perm_etheraddr Get the permanent address from NVRAM authorize restrict traffic to 802.1X packets until 802.1X authorization succeeds deauthorize do not restrict traffic to 802.1X packets until 802.1X authorization succeeds deauthenticate deauthenticate a STA from the AP with optional reason code (AP ONLY) wsec wireless security bit vector 1 - WEP enabled 2 - TKIP enabled 4 - AES enabled 8 - WSEC in software 0x80 - FIPS enabled 0x100 - WAPI enabled auth set/get 802.11 authentication type. 0 = OpenSystem, 1= SharedKey, 2=Open/Shared wpa_auth Bitvector of WPA authorization modes: 1 WPA-NONE 2 WPA-802.1X/WPA-Professional 4 WPA-PSK/WPA-Personal 64 WPA2-802.1X/WPA2-Professional 128 WPA2-PSK/WPA2-Personal 0 disable WPA wpa_cap set/get 802.11i RSN capabilities set_pmk Set passphrase for PMK in driver-resident supplicant. scan Initiate a scan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan iscan_s Initiate an incremental scan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan iscan_c Continue an incremental scan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan scancache_clear clear the scan cache escan Start an escan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan escanabort Abort an escan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan passive Puts scan engine into passive mode regulatory Get/Set regulatory domain mode (802.11d). Driver must be down. spect Get/Set 802.11h Spectrum Management mode. 0 - Off 1 - Loose interpretation of 11h spec - may join non-11h APs 2 - Strict interpretation of 11h spec - may not join non-11h APs 3 - Disable 11h and enable 11d 4 - Loose interpretation of 11h+d spec - may join non-11h APs scanresults Return results from last scan. iscanresults Return results from last iscan. Specify a buflen (max 8188) to artificially limit the size of the results buffer. iscanresults [buflen] assoc Print information about current network association. (also known as "status") status Print information about current network association. (also known as "assoc") disassoc Disassociate from the current BSS/IBSS. chanlist Deprecated. Use channels. channels Return valid channels for the current settings. channels_in_country Return valid channels for the country specified. Arg 1 is the country abbreviation Arg 2 is the band(a or b) curpower Return current tx power settings. -q (quiet): estimated power only. txinstpwr Return tx power based on instant TSSI scansuppress Suppress all scans for testing. 0 - allow scans 1 - suppress scans evm Start an EVM test on the given channel, or stop EVM test. Arg 1 is channel number 1-14, or "off" or 0 to stop the test. Arg 2 is optional rate (1, 2, 5.5 or 11) rateset Returns or sets the supported and basic rateset, (b) indicates basic With no args, returns the rateset. Args are rateset "default" | "all" | -m default - driver defaults all - all rates are basic rates arbitrary rateset - list of rates arbitrary mcsset - list of mcs rates octets, each bit representing corresponding mcs List of rates are in Mbps and each rate is optionally followed by "(b)" or "b" for a Basic rate. Example: 1(b) 2b 5.5 11 At least one rate must be Basic for a legal rateset. roam_trigger Get or Set the roam trigger RSSI threshold: Get: roam_trigger [a|b] Set: roam_trigger [a|b|all] integer - 0: default 1: optimize bandwidth 2: optimize distance [-1, -99]: dBm trigger value roam_delta Set the roam candidate qualification delta. roam_delta [integer [, a/b]] roam_scan_period Set the roam candidate qualification delta. (integer) suprates Returns or sets the 11g override for the supported rateset With no args, returns the rateset. Args are a list of rates, or 0 or -1 to specify an empty rateset to clear the override. List of rates are in Mbps, example: 1 2 5.5 11 scan_channel_time Get/Set scan channel time scan_unassoc_time Get/Set unassociated scan channel dwell time scan_home_time Get/Set scan home channel dwell time scan_passive_time Get/Set passive scan channel dwell time scan_nprobes Get/Set scan parameter for number of probes to use per channel scanned prb_resp_timeout Get/Set probe response timeout channel_qa Get last channel quality measurment channel_qa_start Start a channel quality measurment country Select Country Code for driver operational region For simple country setting: wl country Where is either a long name or country code from ISO 3166; for example "Germany" or "DE" For a specific built-in country definition: wl country [] Where is a country country code followed by '/' and regulatory revision number. For example, "US/3". And where is either a long name or country code from ISO 3166. If is omitted, it will be the same as the built-in country code. Use 'wl country list [band(a or b)]' for the list of supported countries autocountry_default Select Country Code for use with Auto Contry Discovery join Join a specified network SSID. Usage: join [key <0-3>:xxxxx] [imode bss|ibss] [amode ] is one of: open, shared, openshared, wpa, wpapsk, wpa2, wpa2psk, wpanone Other optional join parameters: bssid xx:xx:xx:xx:xx:xx, BSSID to scan and join channels L comma separated list of channels to search in radioband (5(a) or 2(b/g)) bandwidth, 10,20 or 40 ctlsideband, -1=lower, 0=none, 1=upper prescanned use channel and bssid list from scanresults ssid Set or get a configuration's SSID. wl ssid [-C num]|[--cfg=num] [] If the configuration index 'num' is not given, configuraion #0 is assumed and setting will initiate an assoication attempt if in infrastructure mode, or join/creation of an IBSS if in IBSS mode, or creation of a BSS if in AP mode. mac Set or get the list of source MAC address matches. wl mac xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...] To Clear the list: wl mac none macmode Set the mode of the MAC list. 0 - Disable MAC address matching. 1 - Deny association to stations on the MAC list. 2 - Allow association to stations on the MAC list. wds Set or get the list of WDS member MAC addresses. Set using a space separated list of MAC addresses. wl wds xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...] lazywds Set or get "lazy" WDS mode (dynamically grant WDS membership to anyone). noise Get noise (moving average) right after tx in dBm fqacurcy Manufacturing test: set frequency accuracy mode. freqacuracy syntax is: fqacurcy Arg is channel number 1-14, or 0 to stop the test. crsuprs Manufacturing test: set carrier suppression mode. carriersuprs syntax is: crsuprs Arg is channel number 1-14, or 0 to stop the test. longtrain Manufacturing test: set longtraining mode. longtrain syntax is: longtrain Arg is A band channel number or 0 to stop the test. band Returns or sets the current band auto - auto switch between available bands (default) a - force use of 802.11a band b - force use of 802.11b band bands Return the list of available 802.11 bands phylist Return the list of available phytypes shortslot Get current 11g Short Slot Timing mode. (0=long, 1=short) shortslot_override Get/Set 11g Short Slot Timing mode override. (-1=auto, 0=long, 1=short) shortslot_restrict Get/Set AP Restriction on associations for 11g Short Slot Timing capable STAs. 0 - Do not restrict association based on ShortSlot capability 1 - Restrict association to STAs with ShortSlot capability ignore_bcns AP only (G mode): Check for beacons without NONERP element(0=Examine beacons, 1=Ignore beacons) pktcnt Get the summary of good and bad packets. upgrade Upgrade the firmware on an embedded device gmode Set the 54g Mode (LegacyB|Auto||GOnly|BDeferred|Performance|LRS) gmode_protection Get G protection mode. (0=disabled, 1=enabled) gmode_protection_control Get/Set 11g protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS) gmode_protection_override Get/Set 11g protection mode override. (-1=auto, 0=disable, 1=enable) protection_control Get/Set protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS) legacy_erp Get/Set 11g legacy ERP inclusion (0=disable, 1=enable) scb_timeout AP only: inactivity timeout value for authenticated stas assoclist AP only: Get the list of associated MAC addresses. isup Get driver operational state (0=down, 1=up) rssi Get the current RSSI val, for an AP you must specify the mac addr of the STA rssi_event Set parameters associated with RSSI event notification usage: wl rssi_event rate_limit: Number of events posted to application will be limited to 1 per this rate limit. Set to 0 to disable rate limit. rssi_levels: Variable number of RSSI levels (maximum 8) in increasing order (e.g. -85 -70 -60). An event will be posted each time the RSSI of received beacons/packets crosses a level. fasttimer Deprecated. Use fast_timer. slowtimer Deprecated. Use slow_timer. glacialtimer Deprecated. Use glacial_timer. radar Enable/Disable radar radarargs Get/Set Radar parameters in order as version, npulses, ncontig, min_pw, max_pw, thresh0, thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp, min_fm_lp, max_span_lp, min_deltat, max_deltat, autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra, npulses_stg2, npulses_stg3, percal_mask, quant, min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask radarargs40 Get/Set Radar parameters for 40Mhz channel in order as version, npulses, ncontig, min_pw, max_pw, thresh0, thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp, min_fm_lp, max_span_lp, min_deltat, max_deltat, autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra, npulses_stg2, npulses_stg3, percal_mask, quant, min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask radarthrs Set Radar threshold for both 20 & 40MHz BW: order as thresh0_20_lo, thresh1_20_lo, thresh0_40_lo, thresh1_40_lo thresh0_20_hi, thresh1_20_hi, thresh0_40_hi, thresh1_40_hi dfs_status Get dfs status interference Get/Set interference mitigation mode. Choices are: 0 = none 1 = non wlan 2 = wlan manual 3 = wlan automatic 4 = wlan automatic with noise reduction interference_override Get/Set interference mitigation override. Choices are: 0 = no interference mitigation 1 = non wlan 2 = wlan manual 3 = wlan automatic 4 = wlan automatic with noise reduction -1 = remove override, override disabled frameburst Disable/Enable frameburst mode pwr_percent Get/Set power output percentage toe Enable/Disable tcpip offload feature toe_ol Get/Set tcpip offload components toe_stats Display checksum offload statistics toe_stats_clear Clear checksum offload statistics arpoe Enable/Disable arp agent offload feature arp_ol Get/Set arp offload components arp_peerage Get/Set age of the arp entry in minutes arp_table_clear Clear arp cache arp_hostip Add a host-ip address or display them arp_hostip_clear Clear all host-ip addresses arp_stats Display ARP offload statistics arp_stats_clear Clear ARP offload statistics wet Get/Set wireless ethernet bridging mode bi Get/Set the beacon period (bi=beacon interval) dtim Get/Set DTIM wds_remote_mac Get WDS link remote endpoint's MAC address wds_wpa_role_old Get WDS link local endpoint's WPA role (old) wds_wpa_role Get/Set WDS link local endpoint's WPA role authe_sta_list Get authenticated sta mac address list autho_sta_list Get authorized sta mac address list measure_req Send an 802.11h measurement request. Usage: wl measure_req Measurement types are: TPC, Basic, CCA, RPI Target MAC addr format is xx:xx:xx:xx:xx:xx quiet Send an 802.11h quiet command. Usage: wl quiet , , csa Send an 802.11h channel switch anouncement with chanspec: [a,b][n][u,l] mode (0 or 1) count (0-254) channel number (0-224) band a=5G, b=2G bandwidth n=10, non for 20 & 40 ctl sideband, l=lower, u=upper, default no ctl sideband constraint Send an 802.11h Power Constraint IE Usage: wl constraint 1-255 db rm_req Request a radio measurement of type basic, cca, or rpi specify a series of measurement types each followed by options. example: wl rm_req cca -c 1 -d 50 cca -c 6 cca -c 11 Options: -t n numeric token id for measurement set or measurement -c n channel -d n duration in TUs (1024 us) -p parallel flag, measurement starts at the same time as previous Each measurement specified uses the same channel and duration as the previous unless a new channel or duration is specified. rm_rep Get current radio measurement report join_pref Set/Get join target preferences. assoc_pref Set/Get association preference. Usage: wl assoc_pref [auto|a|b|g] wme Set WME (Wireless Multimedia Extensions) mode (0=off, 1=on, -1=auto) wme_ac wl wme_ac ap|sta [be|bk|vi|vo [ecwmax|ecwmin|txop|aifsn|acm ] ...] wme_apsd Set APSD (Automatic Power Save Delivery) mode on AP (0=off, 1=on) wme_apsd_sta Set APSD parameters on STA. Driver must be down. Usage: wl wme_apsd_sta : number of frames per USP: 0 (all), 2, 4, or 6 : value 0 to disable, 1 to enable U-APSD per AC wme_dp Set AC queue discard policy. Usage: wl wme_dp : value 0 for newest-first, 1 for oldest-first wme_counters print WMM stats wme_clear_counters clear WMM counters wme_tx_params wl wme_tx_params [be|bk|vi|vo [short|sfb|long|lfb|max_rate ] ...] wme_maxbw_params wl wme_maxbw_params [be|bk|vi|vo ....] lifetime Set Lifetime parameter (milliseconds) for each ac. wl lifetime be|bk|vi|vo [] reinit Reinitialize device sta_info wl sta_info cap driver capabilities malloc_dump Deprecated. Folded under 'wl dump malloc chan_info channel info add_ie Add a vendor proprietary IE to 802.11 management packets Usage: wl add_ie length OUI hexdata : Bit 0 - Beacons Bit 1 - Probe Rsp Bit 2 - Assoc/Reassoc Rsp Bit 3 - Auth Rsp Bit 4 - Probe Req Bit 5 - Assoc/Reassoc Req Example: wl add_ie 3 10 00:90:4C 0101050c121a03 to add this IE to beacons and probe responses del_ie Delete a vendor proprietary IE from 802.11 management packets Usage: wl del_ie length OUI hexdata : Bit 0 - Beacons Bit 1 - Probe Rsp Bit 2 - Assoc/Reassoc Rsp Bit 3 - Auth Rsp Bit 4 - Probe Req Bit 5 - Assoc/Reassoc Req Example: wl del_ie 3 10 00:90:4C 0101050c121a03 list_ie Dump the list of vendor proprietary IEs rand Get a 2-byte Random Number from the MAC's PRNG Usage: wl rand otpw Write an srom image to on-chip otp Usage: wl otpw file nvotpw Write nvram to on-chip otp Usage: wl nvotpw file bcmerrorstr errorstring freqtrack Set Frequency Tracking Mode (0=Auto, 1=On, 2=OFF) eventing set/get 128-bit hex filter bitmask for MAC event reporting up to application layer event_msgs set/get 128-bit hex filter bitmask for MAC event reporting via packet indications counters Return driver counter values delta_stats_interval set/get the delta statistics interval in seconds (0 to disable) delta_stats get the delta statistics for the last interval assoc_info Returns the assoc req and resp information [STA only] autochannel auto channel selection: 1 to issue a channel scanning; 2 to set chanspec based on the channel scan result; without argument to only show the chanspec selected; ssid must set to null before this process, RF must be up csscantimer auto channel scan timer in minutes (0 to disable) closed hides the network from active scans, 0 or 1. 0 is open, 1 is hide pmkid_info Returns the pmkid table abminrate get/set afterburner minimum rate threshold bss set/get BSS enabled status: up/down closednet set/get BSS closed network attribute ap_isolate set/get AP isolation eap_restrict set/get EAP restriction diag diag testindex(1-interrupt, 2-loopback, 3-memory, 4-led); precede by 'wl down' and follow by 'wl up' reset_d11cnts reset 802.11 MIB counters staname get/set station name: Maximum name length is 15 bytes apname get AP name otpdump Dump raw otp otpstat Dump OTP status nrate -r legacy rate (CCK, OFDM)-m mcs index-s stf mode (0=SISO,1=CDD,2=STBC(not supported),3=SDM)-w Override mcs only to support STA's with/without STBC capability mimo_txbw get/set mimo txbw (2=20Mhz(lower), 3=20Mhz upper, 4=40Mhz, 5=40Mhz dup (On/Off) rifs_advert set/get the rifs mode advertisement status; usage: wl rifs_advert <-1/0> (Auto/Off) phy_rxiqest Get phy RX IQ noise in dBm: -s # of samples (2^n) -a antenna select, 0,1 or 3 phy_txiqcc usage: phy_txiqcc [a b] Set/get the iqcc a, b values phy_txlocc usage: phy_txlocc [di dq ei eq fi fq] Set/get locc di dq ei eq fi fq values phytable usage: wl phytable table_id offset width_of_table_element [table_element] Set/get table element of a table with the given ID at the given offset Note that table width supplied should be 8 or 16 or 32 table ID, table offset can not be negative pavars Set/get temp PA parameters usage: wl down wl pavars pa2gw0a0=0x1 pa2gw1a0=0x2 pa2gw2a0=0x3 ... wl pavars wl up override the PA parameters after driver attach(srom read), before diver up These override values will be propogated to HW when driver goes up PA parameters in one band range (2g, 5gl, 5g, 5gh) must all present if one of them is specified in the command, otherwise it will be filled with 0 povars Set/get temp power offset usage: wl down wl povars cck2gpo=0x1 ofdm2gpo=0x2 mcs2gpo=0x3 ... wl povars wl up override the power offset after driver attach(srom read), before diver up These override values will be propogated to HW when driver goes up power offsets in one band range (2g, 5gl, 5g, 5gh) must all present if one of them is specified in the command, otherwise it will be filled with 0 cck(2g only), ofdm, and mcs(0-7) for NPHY are supported fem Set temp fem2g/5g value usage: wl fem (tssipos2g=0x1 extpagain2g=0x2 pdetrange2g=0x1 triso2g=0x1 antswctl2g=0) (tssipos5g=0x1 extpagain5g=0x2 pdetrange5g=0x1 triso5g=0x1 antswctl5g=0) antgain Set temp ag0/1 value usage: wl antgain ag0=0x1 ag1=0x2 maxpower Set temp maxp2g(5g)a0(a1) value usage: wl maxpower maxp2ga0=0x1 maxp2ga1=0x2 maxp5ga0=0xff maxp5ga1=0xff maxp5gla0=0x3 maxp5gla1=0x4 maxp5gha0=0x5 maxp5gha1=0x6 phy_antsel get/set antenna configuration set: -1(AUTO), 0xAB(fixed antenna selection) where A and B is the antenna numbers used for RF chain 0 and 1 respectively query: [AUTO] [AUTO] [AUTO] [AUTO] where utx = TX unicast antenna configuration urx = RX unicast antenna configuration dtx = TX default (non-unicast) antenna configuration drx = RX default (non-unicast) antenna configuration txcore Usage: wl txcore -k -o -s <1..4> -c -k CCK core mask -o OFDM core mask -s # of space-time-streams -c active core (bitmask) to be used when transmitting frames sample_collect Optional parameters HTPHY/(NPHY with NREV >= 7) are: -f File name to dump the sample buffer (default "sample_collect.dat") -t Trigger condition (default now) now, good_fcs, bad_fcs, bad_plcp, crs, crs_glitch, crs_deassert -b PreTrigger duration in us (default 10) -a PostTrigger duration in us (default 10) -m Sample collect mode (default 1) HTPHY: 0=adc, 1..3=adc+rssi, 4=gpio NPHY: 1=Dual-Core adc[9:2], 2=Core0 adc[9:0], 3=Core1 adc[9:0], gpio=gpio -g GPIO mux select (default 0) use only for gpio mode -d Downsample enable (default 0) use only for HTPHY -e BeDeaf enable (default 0) -i Timeout in units of 10us (default 1000) Optional parameters (NPHY with NREV < 7) are: -f File name to dump the sample buffer (binary format, default "sample_collect.dat") -u Sample collect duration in us (default 60) -c Cores to do sample collect, only if BW=40MHz (default both) For (NREV < 7), the NPHY buffer returned has the format: In 20MHz [(uint16)num_bytes, ] In 40MHz [(uint16)num_bytes(core0), , (uint16)num_bytes(core1), ] txfifo_sz set/get the txfifo size; usage: wl txfifo_sz pfnset Configures preferred network offload parameter pfnset syntax is: pfnset [scanfrq xxxxx(30 sec)] [netimeout xxxx(60 sec)][rssi_delta xxxx(30 dBm)] [sort (listorder)|rssi] [bkgscan (0)|1][immediate 0|(1)] pfnadd Adding SSID based preferred networks to monitor and connect pfnadd syntax is: pfnadd ssid [imode (bss)|ibss][amode (open)|shared] [wpa_auth (wpadisabled)|wpapsk|wpa2psk|wpanone][wsec WEP|TKIP|AES|TKIPAES] pfn Enable/disable preferred network off load monitoring pfn syntax is: pfn 0|1 pfnclear Clear the preferred network list pfnclear syntax is: pfnclear pfneventchk Listen and prints the preferred network off load event from dongle pfneventchk syntax is: pfneventchk [(eth1)ifname] escan_event_check Listen and prints the escan events from the dongle escan_event_check syntax is: escan_event_check ifname flag flag 1 = sync_id info, 2 = bss info, 4 = state + bss info [default], 8 = TLV check for IEs escanresults Start escan and display results. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan event_filter Set/get event filter event_filter syntax is: event_filter [value] rate_histo Usage: a) wl rate_histo b) wl rate_histo (MAC address e.g. 00:11:20:11:33:33) (Access Category(AC) - 0x10:for entire MAC or 0x4:for video AC for this MAC) (num_pkts (optional) - Number of packets to average - max 64 for AC 0x10, max 32 for AC 0x4) pkteng_start start packet engine tx usage: wl pkteng_start [(async)|sync] [ipg] [len] [nframes] [src] start packet engine rx usage: wl pkteng_start [(async)|sync] [rxframes] [rxtimeout] sync: synchronous mode ipg: inter packet gap in us len: packet length nframes: number of frames; 0 indicates continuous tx test src: source mac address rxframes: number of receive frames (sync mode only) rxtimeout: maximum timout in msec (sync mode only) pkteng_stop stop packet engine; usage: wl pkteng_stop pkteng_stats packet engine stats; usage: wl pkteng_stats wowl Enable/disable WOWL events 0 - Clear all events Bit 0 - Wakeup on Magic Packet Bit 1 - Wakeup on NetPattern (use 'wl wowl_pattern' to configure pattern) Bit 2 - Wakeup on loss-of-link due to Disassociation/Deauth Bit 3 - Wakeup on retrograde tsf Bit 4 - Wakeup on loss of beacon (use 'wl wowl_bcn_loss' to configure time) wowl_bcn_loss Set #of seconds of beacon loss for wakeup event wowl_pattern usage: wowl_pattern [ [clr | [[ add | del ] offset mask value ]]] No options -- lists existing pattern list add -- Adds the pattern to the list del -- Removes a pattern from the list clr -- Clear current list offset -- Starting offset for the pattern mask -- Mask to be used for pattern. Bit i of mask => byte i of the pattern value -- Value of the pattern wowl_wakeind usage: wowl_wakeind [clear] Shows last system wakeup event indications from PCI and D11 cores clear - Clear the indications wowl_status usage: wowl_status [clear] Shows last system wakeup setting lpphy_txiqcc usage: lpphy_txiqcc [a b] Set/get the iqcc a, b values lpphy_txlocc usage: lpphy_txlocc [di dq ei eq fi fq] Set/get locc di dq ei eq fi fq values phytable usage: wl phytable table_id offset width_of_table_element [table_element] Set/get table element of a table with the given ID at the given offset Note that table width supplied should be 8 or 16 or 32 table ID, table offset can not be negative pavars Set/get temp PA parameters usage: wl down wl pavars pa2gw0a0=0x1 pa2gw1a0=0x2 pa2gw2a0=0x3 ... wl pavars wl up override the PA parameters after driver attach(srom read), before diver up These override values will be propogated to HW when driver goes up PA parameters in one band range (2g, 5gl, 5g, 5gh) must all present if one of them is specified in the command, otherwise it will be filled with 0 povars Set/get temp power offset usage: wl down wl povars cck2gpo=0x1 ofdm2gpo=0x2 mcs2gpo=0x3 ... wl povars wl up override the power offset after driver attach(srom read), before diver up These override values will be propogated to HW when driver goes up power offsets in one band range (2g, 5gl, 5g, 5gh) must all present if one of them is specified in the command, otherwise it will be filled with 0 cck(2g only), ofdm, and mcs(0-7) for NPHY are supported fem Set temp fem2g/5g value usage: wl fem (tssipos2g=0x1 extpagain2g=0x2 pdetrange2g=0x1 triso2g=0x1 antswctl2g=0) (tssipos5g=0x1 extpagain5g=0x2 pdetrange5g=0x1 triso5g=0x1 antswctl5g=0) antgain Set temp ag0/1 value usage: wl antgain ag0=0x1 ag1=0x2 maxpower Set temp maxp2g(5g)a0(a1) value usage: wl maxpower maxp2ga0=0x1 maxp2ga1=0x2 maxp5ga0=0xff maxp5ga1=0xff maxp5gla0=0x3 maxp5gla1=0x4 maxp5gha0=0x5 maxp5gha1=0x6 wowl_pkt Send a wakeup frame to wakup a sleeping STA in WAKE mode Usage: wl wowl_pkt >[ magic [] | net ] e.g. To send bcast magic frame -- wl wowl_pkt 102 bcast magic 00:90:4c:AA:BB:CC To send ucast magic frame -- wl wowl_pkt 102 ucast 00:90:4c:aa:bb:cc magic To send a frame with L2 unicast - wl wowl_pkt 102 00:90:4c:aa:bb:cc net 0 0x00904caabbcc NOTE: offset for netpattern frame starts from "Dest EA" of ethernet frame.So dest ea will be used only when offset is >= 6 wme_apsd_trigger Set Periodic APSD Trigger Frame Timer timeout in ms (0=off) wme_autotrigger Enable/Disable sending of APSD Trigger frame when all ac are delivery enabled reassoc Initiate a (re)association request. Usage: wl reassoc [options] Options: -c CL, --chanspecs=CL chanspecs (comma or space separated list) send_nulldata Sed a null frame to the specified hw address btc_params g/set BT Coex parameters btc_flags g/set BT Coex flags obss_scan_params set/get Overlapping BSS scan parameters Usage: wl obss_scan a b c d e ...; where a-Passive Dwell, {5-1000TU}, default = 100 b-Active Dwell, {10-1000TU}, default = 20 c-Width Trigger Scan Interval, {10-900sec}, default = 300 d-Passive Total per Channel, {200-10000TU}, default = 200 e-Active Total per Channel, {20-1000TU}, default = 20 f-Channel Transition Delay Factor, {5-100}, default = 5 g-Activity Threshold, {0-100%}, default = 25 mkeep_alive Send specified "mkeep-alive" packet periodically. Usage: wl mkeep_alive index: 0 - 3. period: Re-transmission period in milli-seconds. 0 to disable packet transmits. packet: Hex packet contents to transmit. The packet contents should include the entire ethernet packet (ethernet header, IP header, UDP header, and UDP payload) specified in network byte order. If no packet is specified, a nulldata frame will be sent instead. e.g. Send keep alive packet every 30 seconds using id-1: wl mkeep_alive 1 30000 0x0014a54b164f000f66f45b7e08004500001e000040004011c52a0a8830700a88302513c413c4000a00000a0d keep_alive Send specified "keep-alive" packet periodically. Usage: wl keep_alive period: Re-transmission period in milli-seconds. 0 to disable packet transmits. packet: Hex packet contents to transmit. The packet contents should include the entire ethernet packet (ethernet header, IP header, UDP header, and UDP payload) specified in network byte order. e.g. Send keep alive packet every 30 seconds: wl keep_alive 30000 0x0014a54b164f000f66f45b7e08004500001e000040004011c52a0a8830700a88302513c413c4000a00000a0d srchmem g/set ucode srch engine memory pkt_filter_add Install a packet filter. Usage: wl pkt_filter_add id: Integer. User specified id. type: 0 (Pattern matching filter). offset: Integer. Offset within received packets to start matching. polarity: Set to 1 to negate match result. 0 is default. bitmask: Hex bitmask that indicates which bits of 'pattern' to match. Must be same size as 'pattern'. Bit 0 of bitmask corresponds to bit 0 of pattern, etc. If bit N of bitmask is 0, then do *not* match bit N of the pattern with the received payload. If bit N of bitmask is 1, then perform match. pattern: Hex pattern to match. pkt_filter_clear_stats Clear packet filter statistic counter values. Usage: wl pkt_filter_clear_stats pkt_filter_enable Enable/disable a packet filter. Usage: wl pkt_filter_enable <0|1> pkt_filter_list List installed packet filters. Usage: wl pkt_filter_list [val] val: 0 (disabled filters) 1 (enabled filters) pkt_filter_mode Set packet filter match action. Usage: wl pkt_filter_mode value: 1 - Forward packet on match, discard on non-match (default). 0 - Discard packet on match, forward on non-match. pkt_filter_delete Uninstall a packet filter. Usage: wl pkt_filter_delete pkt_filter_stats Retrieve packet filter statistic counter values. Usage: wl pkt_filter_stats seq_start Initiates command batching sequence. Subsequent IOCTLs will be queued until seq_stop is received. seq_stop Defines the end of command batching sequence. Queued IOCTLs will be executed. seq_delay Driver should spin for the indicated amount of time. It is only valid within the context of batched commands. seq_error_index Used to retrieve the index (starting at 1) of the command that failed within a batch bmac_reboot Reboot BMAC findserver Used to find the remote server with proper mac address given by the user,this cmd is specific to wifi protocol. txmcsset get Transmit MCS rateset for 11N device rxmcsset get Receive MCS rateset for 11N device mimo_ss_stf get/set SS STF mode. Usage: wl mimo_ss_stf <-b a | b> value: 0 - SISO; 1 - CDD -b(band): a - 5G; b - 2.4G extlog get external logs Usage: wl extlog rom_last: 1 - from the last log record; 0 - whole log recrods number: number of log records to get, MAX is 32. extlog_clr clear external log records extlog_cfg get/set external log configuration assertlog get external assert logs Usage: wl assertlog assert_bypass set/get the asset_bypass flag; usage: wl assert_bypass <1/0> (On/Off) ledbh set/get led behavior Usage: wl ledbh [0-3] [0-15] obss_coex_action send OBSS 20/40 Coexistence Mangement Action Frame Usage: wl obss_coex_action -i <1/0> -w <1/0> -c -i: 40MHz intolerate bit; -w: 20MHz width Req bit; -c: channel list, 1 - 14 At least one option must be provided chanim_state get channel interference state Usage: wl chanim_state channel Valid channels: 1 - 14 returns: 0 - Acceptable; 1 - Severe chanim_mode get/set channel interference measure (chanim) mode Usage: wl chanim_mode value: 0 - disabled; 1 - detection only; 2 - detection and avoidance ledbh set/get led behavior Usage: wl ledbh [0-3] [0-15] led_blink_sync set/get led_blink_sync Usage: wl led_blink_sync [0-3] [0/1] cca_get_stats Usage: wl cca_stats [-c channel] [-s num seconds][-a] -c channel: Optional. specify channel. 0 = All channels. Default = current channel -s num_seconds: Optional. Default = 10, Max = 60 -i: list individual measurements in addition to the averages -curband: Only recommend channels on current band smfstats get/clear selected management frame (smf) stats wl smfstats [-C num]|[--cfg=num] [auth]|[assoc]|[reassoc]|[clear] clear - to clear the stats dongleset Enable uart driver manfinfo show chip package info in OTP rrm_nbr_req send 11k neighbor report measurement request Usage: wl 11k_nbr_req [ssid] p2p_ssid set WiFi P2P wildcard ssid. Usage: wl p2p_ssid p2p_state set WiFi P2P discovery state. Usage: wl p2p_state [ ] p2p_scan initiate WiFi P2P scan. Usage: wl p2p_scan S|E Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan p2p_ifadd add WiFi P2P interface Usage: wl p2p_ifadd go|client|dyngo [chanspec] MAC-address: xx:xx:xx:xx:xx:xx p2p_ifdel delete WiFi P2P interface Usage: wl p2p_ifdel MAC-address: xx:xx:xx:xx:xx:xx p2p_ifupd update an interface to WiFi P2P interface Usage: wl p2p_ifupd go|client MAC-address: xx:xx:xx:xx:xx:xx p2p_if query WiFi P2P interface bsscfg index Usage: wl p2p_if MAC-address: xx:xx:xx:xx:xx:xx p2p_noa set/get WiFi P2P NoA schedule Usage: wl p2p_noa type 0: Scheduled Absence (on GO): action -1: Cancel the schedule: action 0,1,2: